How to cancel one object mid-print without wrecking the rest of the plate
One part pops loose in the middle of a full plate while everything around it prints fine. You don't always have to scrap the whole job. This guide shows how to tell whether a part can be canceled on its own, how to pick the right one, and when stopping everything is the only way to avoid a crash.
The short answer
You can cancel one object on a 3D print plate only if it is a separate object in your slicer project and your printer's firmware supports per-object canceling. According to Prusa's documentation, the MK4/S, MK3.9/S, XL/+, CORE One+/GEN 2 and MINI/+ offer it under Tune, then Cancel Object. The Cancel Current option cancels whichever object the nozzle is printing right then. The print keeps running and the printer skips every G-code command tied to the canceled object. Stop the entire plate instead if the failed part has slid into the toolhead's path or filament is wrapping around the nozzle, because a canceled part still sits on the bed.
What makes a part separable on the plate
Canceling a single part only works when your plate holds several distinct objects printed together, layer by layer. Prusa's knowledge base describes exactly this situation. When you print several objects at once, one of them may come out rough or break loose from the plate while the rest print perfectly. That is what the Cancel Object feature is for.
A separable part exists as its own object in your slicer project. It sits next to the others without touching them. Parts merged into one mesh, an assembly combined into a single body, or a batch imported as one block can't be split the same way, because the printer sees them as a single object. Before you send a crowded plate, open the slicer's object list and confirm that every part has its own entry. In PrusaSlicer, that list also shows each part's name and print order. Take a minute to skim it. This check saves you from finding out mid-failure that your whole batch is one inseparable lump.
Matching the failing part to the preview and the printer menu
The tricky part is connecting the piece you see peeling up with the entry on the printer's screen. On a plate of identical parts, it's easy to cancel the neighbor while the bad one keeps printing. Before you hit print, make a habit of noting where each object sits: front left, center, back right. A quick phone photo of the slicer preview is enough.
Prusa's documentation calls Cancel Current, in the same submenu, the easiest option. You wait until the nozzle reaches the object you want gone, then select it. The toolhead points out the right part for you, so there's no guessing from a list. If you watch prints remotely, a workshop camera helps you confirm which part is failing before you touch anything. On another brand, check the manufacturer's official documentation for an equivalent feature. Menu names vary between brands, and some printers don't offer per-object canceling at all, so find out before your first big plate.
Canceling the object from the printer menu
Prusa's article lists the supported printers: MK4/S, MK3.9/S, XL/+, CORE One+/GEN 2 and MINI/+. During a print, open Tune, then Cancel Object, and pick the object you want to stop. The print keeps going, but the printer skips every G-code command tied to the canceled object. The other parts carry on, layer after layer.
Two details matter here. First, canceling isn't necessarily final. Prusa notes that you can resume a canceled object from the same submenu. That helps if you picked the wrong part, as long as you catch it quickly, since any layers skipped in the meantime will be missing from that part. Second, canceling an object doesn't remove it from the bed. The failed part stays put, at whatever height it reached, along with any loose strands of filament. That leftover is what decides whether you can safely keep going. Watch it closely right after you cancel, and for the next several layers.
When to stop the whole plate instead
Canceling one part protects the rest of the plate only while the toolhead can move freely. Once that's no longer true, stop the entire print. The classic case is a part that broke free and slid across the bed into the path of other objects. Even after you cancel it, it's still an obstacle. The nozzle can clip it while moving between parts, drag it along, or shove it into a good part.
Make the same call if filament is wrapping around the nozzle, a blob is building up on the hotend, or a loosened part is leaning toward its neighbors. At that point the problem isn't one object anymore. It's the machine. A print that has turned into spaghetti falls squarely in this category. A part with one corner lifting slightly but still firmly attached is a good candidate for a targeted cancel. So is a surface flaw limited to a single part. When in doubt, a full stop costs you one plate of parts. A crash can damage the nozzle or the build surface.
Setting up the plate so a targeted cancel stays an option
The best time to handle a failed part is before the print starts. Space objects out instead of packing them tight, so a part that comes loose is less likely to reach its neighbor. Put fragile parts, tall and thin ones or those with a small footprint, where you can easily keep an eye on them. Also confirm that everything fits the build volume. Berkeley Lab's pre-print checklist says to check a part's overall dimensions against the printer's build envelope and to split it into smaller pieces if it's too big.
On the file side, the same checklist prefers 3MF, which avoids the rounding errors and unit mix-ups common with STL. Our STL vs 3MF guide covers that choice. Finally, give each object a clear name in your project. If your printer shows object names, telling left clip from right clip takes a second instead of guessing between two nearly identical entries while a part is failing.
Sequential printing as a damage-control alternative
If you regularly print batches of small parts, there's another approach: finish objects one at a time instead of building them all together. PrusaSlicer's documentation describes this sequential mode. Its listed benefits include less stringing and oozing, better layer adhesion, and, most relevant here, a lower chance that one failed part ruins the others. You turn it on under Print settings, Output options, Complete individual objects, then press A to auto-arrange the plate for safe sequential printing.
The tradeoff is collision risk. The extruder, rods and cables have to clear parts that are already finished. PrusaSlicer handles collision avoidance on supported Prusa printers. For other machines, it falls back on generic extruder clearance settings. If you move objects and a possible collision is detected, an error message names the affected object, but it doesn't block G-code export, so review it before printing. Press E in the 3D view to see the print order on the objects. Starting with version 2.9.1, and only for Prusa printers, the preview can also show a 3D model of the extruder.
Sources and limits
- Prusa — Cancel Object
- PrusaSlicer — Sequential printing
- Berkeley Lab — Pre-Print Checklist
We organize manufacturer and community documentation; we have not measured these products ourselves. The manual for your exact model takes precedence over general guidance.
A clearer shortlist starts with your projects.
Use the free buying checklist and budget worksheet before comparing offers.