Grooved spacing blocks you can 3D print for accurate dry fits
A dry fit only tells you something if every gap matches. You also need spacers that stay put when you reach for the next clamp. Printed grooved blocks can do both if you treat them like real shop tooling. This guide covers reference faces, groove sizing, labeling, retention checks and easy removal.
The short answer
A 3D printed grooved spacing block straddles the edge of a board and holds a consistent gap during dry assembly. Start by choosing the reference faces that will touch the wood. Size the groove from the stock's measured thickness, not its nominal size. Then dial in clearance with a test coupon, since the Prusa Knowledge Base says no single tolerance value works everywhere. Deboss the size on a face that never touches the work, and add a pull tab plus a chamfered lead-in so the block comes off by hand.
What a grooved spacer does during a dry fit
A dry fit is a full rehearsal of a glue-up without the glue. You check dimensions, square and clamp order before anything gets messy. A grooved spacing block slips over the edge of a panel, rail or stile and holds a set distance to the next part. It replaces the scraps of plywood people wedge in by feel, which fall out the moment a clamp shifts.
Formlabs files this kind of part under manufacturing aids, alongside jigs, guides and alignment pins. Its white paper points out that shop tooling doesn't always need to be metal: it depends on the forces the part sees. A spacing block takes light loads, so it's a good fit for an FDM printer. The real payoff is repeatability. A matched set of blocks gives you the same gap across the whole cabinet. And when one disappears under the bench, you reprint an exact copy from the same file instead of cutting a new one and hoping it matches.
Pick your reference faces first
Every block has two kinds of faces. Reference faces touch the wood and set the gap, so they have to be flat and dimensioned with care. Everything else is for grip, labels and storage. Settle that split in your first sketch, because it drives how you orient the part on the bed.
The face printed against the bed is usually the flattest, but the first layers can flare out slightly. A small chamfer on that bottom edge keeps the bulge described in our elephant's foot fix off your reference surface. The Prusa Knowledge Base also recommends chamfers over fillets on bed-facing edges, since a fillet there creates a very steep overhang. Vertical walls carry layer lines. They work as reference faces as long as your target gap tolerates that texture. Mark the reference side with a feature built into the model, such as a debossed arrow, so nobody flips a block around halfway through a glue-up.
Sizing the groove to the actual stock
Size the groove from what the board actually measures, not what the label says. Plywood and dimensional lumber often run off nominal, so take caliper readings at several spots along the edge. Then write down the gap you want between parts. That number becomes the material thickness between the block's reference faces.
On clearance, the Prusa Knowledge Base is blunt: there's no universal value. It notes that an Original Prusa is accurate to at least 0.2 mm, that some materials shrink or warp during printing, and that at least 0.3 mm is a good starting point for parts that need to move. A spacing block sits between those cases. It has to hold on by itself and still come off by hand. Print a coupon with several groove widths, try each one on scrap from the same sheet, and carry the winner back into your model. The assembly clearance calculator turns those coupon results into a number you can use.
Labeling sizes so sets never get mixed up
Spacers of different sizes pile up fast and they all look alike. Put the gap size and a set name on each block, on a face that never touches the work. Grab the wrong block by mistake and the whole dry fit is off without any visible sign.
According to the Prusa Knowledge Base, PrusaSlicer's Text tool opens when you select a model and press T. The Subtracted option creates a negative volume that debosses the text, so no raised lettering throws off a face. Text presets save the font, height and depth, which keeps markings consistent from one set to the next. Our guide to adding text and raised lettering covers other software too. If you run several sets, give each one its own filament color and name the source file with the gap and groove width. Formlabs makes the case for moving from physical to digital inventory, and it fits here: a lost block is a reprint, not a rebuild.
Checking retention on scrap
Test on a cutoff from the same sheet, kept in the same room as the project, because wood moves with humidity. A good block stays on when you tilt the panel, leaves no mark on the edge and comes off without tools. If it drops off, tighten the groove in small steps. If you have to force it or it crushes the fibers, open it up.
Check how it holds up over a full session too. A block that rides through a long clamping sequence takes bumps and repeated pressure. Material matters here, and our page on filament for workshop jigs compares the usual choices. The Prusa Knowledge Base notes that tougher filaments like PETG or ASA may not print small details as cleanly as PLA, so keep grooves and labels simple. And don't treat a printed spacer as a safety stop on a power tool. It's an assembly reference and nothing more.
Designing for easy removal
Removal tends to be an afterthought until the glue is already spread. Build in something to grab: a tab that sticks out past the edge, a finger notch or a hole for a loop of string. A shallow chamfer at the groove entrance guides the block onto the edge and cuts the effort going on and coming off.
Design within what the process can do. Per the Prusa Knowledge Base, an FDM printer handles overhangs between 45 and 60 degrees cleanly, depending on nozzle and settings, which is enough for a support-free lead-in chamfer. With a 0.4 mm nozzle, PrusaSlicer uses a 0.45 mm extrusion width, and a wall thinner than one perimeter won't print. Skip thin lips along the groove, since they'll snap the first time you pry. A groove open on one side, shaped like a U, also releases more easily than a closed slot that binds at the end of the board.
Sources and limits
- Formlabs — Jigs, fixtures and manufacturing aids
- Prusa — Modeling with 3D printing in mind
- PrusaSlicer — Text tool
We organize manufacturer and community documentation; we have not measured these products ourselves. The manual for your exact model takes precedence over general guidance.
A clearer shortlist starts with your projects.
Use the free buying checklist and budget worksheet before comparing offers.